非贵金属光热材料用于光电化学水氧化:综述
Non‐Noble Photothermal Materials for Photoelectrochemical Water Oxidation
发表于 Advanced Functional Materials 的综述提出非贵金属光热材料用于光电化学水氧化的“材料-热-界面-功能”框架。该综述比较过渡金属氧化物、金属磷族/硫族化物、碳基材料/MXenes 与共轭有机材料四类体系,归纳光谱、空间、动力学和稳定性匹配原则。
- 背景
- 光电化学(PEC)水氧化目前受制于几个环节:太阳光谱利用不完整、载流子复合、界面电荷转移迟缓,以及析氧反应(OER)动力学慢。长波长光子在已有体系里处于未被利用的状态。把非贵金属光热材料与半导体光阳极集成,是一条把这些低能量光子转化为反应界面处或界面附近局域热的路径,从而在不引入贵金属的情况下增加反应可用的能量输入。这篇综述围绕这条路线,梳理材料、热、界面与功能彼此之间的关系。
- 做法
- 综述按材料类别组织,选取四类代表性非贵金属光热材料逐类评述:过渡金属氧化物;金属磷族化合物与硫族化合物;碳基材料与MXene;共轭有机材料。对每一类,讨论集中在四点:光到热的转换路径、界面结构如何搭建、材料在光阳极中承担的多重角色,以及各自的限制。贯穿全篇的另一条线索是局域热对以下四个过程的调控:载流子输运、界面空穴转移、OER动力学和O2气泡行为;作者在讨论这些效应时,强调要把热贡献与同时存在的光学、电子和催化效应区分开来。最后进行跨材料比较,把不同体系的经验归并为设计规则,并落到“材料—热—界面—功能”这一框架上。
- 结论
- 跨材料比较得到四条相互耦合的设计原则:光谱匹配、空间匹配、动力学匹配、稳定性匹配。原文以“耦合”描述它们的关系,说明这几项要一起满足:材料的光吸收范围、热源相对界面的位置、反应动力学与器件稳定性需要同时对上。综述由此提出“材料—热—界面—功能”的框架,作为光热辅助光阳极理性设计的组织方式。摘要层面未给出具体的温度窗口、效率或对照实验数值。
- 意义
- 这篇综述把四类材料放在同一组问题下对照:光到热的路径、界面构筑、多重角色与限制被逐类拆开,再用跨材料比较归并为可操作的设计原则。对从事光阳极界面工程的读者,四条匹配原则提供了选材与结构排布的判据;而“材料—热—界面—功能”框架把热源位置、光谱范围、动力学与稳定性放进同一个设计空间里讨论,使不同材料体系之间可以互相参照,而不是各自表述。
- 局限
- 综述点出的关键难点在于:热贡献与共存的光学、电子、催化贡献难以定量解耦,缺少能同时观测热、电荷与反应的原位(operando)分析;热窗口如何优化尚无定论;真实光照条件下的评价标准也尚未统一。这些也正是各材料类自身限制之外,制约该路线走向实用化的共性障碍。
- 下一步
- 作者给出的推进方向与上述难点对应:建立热与非热贡献的定量解耦方法,发展热—电荷—反应协同的operando分析,优化热窗口,并在接近真实光照的条件下形成标准化评价。综述本身即为这些工作提供了材料—热—界面—功能的对照框架。
原文摘要
出版方登记 · CrossrefPhotoelectrochemical (PEC) water oxidation remains constrained by incomplete solar‐spectrum utilization, carrier recombination, sluggish interfacial charge transfer, and slow oxygen evolution reaction (OER) kinetics. Integrating non‐noble photothermal materials with semiconductor photoanodes offers a promising route to utilize underexploited long‐wavelength photons by converting them into localized heat at or near the reaction interface. This review critically examines four representative material classes‐transition‐metal oxides, metal pnictides and chalcogenides, carbon‐based materials and MXenes, and conjugated organic materials‐with emphasis on their light‐to‐heat conversion pathways, interfacial architectures, multifunctional roles, and limitations. Particular attention is given to how localized heating regulates carrier transport, interfacial hole transfer, OER kinetics, and O 2 ‐bubble dynamics, while distinguishing thermal contributions from coexisting optical, electronic, and catalytic effects. Cross‐material comparison yields four coupled design principles: spectral, spatial, kinetic, and stability matching. Key challenges include quantitative decoupling of thermal and non‐thermal contributions, operando heat‐charge‐reaction analysis, optimization of thermal windows, and standardized evaluation under realistic illumination. Overall, this review provides a material‐heat‐interface‐function framework for the rational design of efficient, durable, and practically relevant photothermal‐assisted photoanodes.
页面未能读取全文,以上为出版方登记的摘要;方法与图表见原文
本页是 AI 精读,不转载论文原文;完整论文(含方法、图表与参考文献)见原文
来源:Advanced Functional Materials · doi.org